Search engine [X] Find Online Advanced Search Advanced Search conference Find Decipher DTC Login: Password: Remember: It is currently April 30, 2014, 07:03
# 1 Posted: April 10, 2010, 15:47 Author Topeka Moderators Off Line Joined: January 11, 2010, 10:50 Posts: inertia 14634 Location: The broken Full name: Dmitry Vehicle: Ford Focus Engine: inertia 1.6 Petrol Transmission: Automatic Climate change: Climate control
<Article in Fyuzhenovedenii> Installation codes necessary details --------------------------------------- ----- Required materials and spare parts Finis Code Number Set switch PAD, installation instructions and customer declaration form: cars, manufactured between October 2005 and 18.04.2006, p online program inertia to maintain stability program (ESP ) 1,405,983 1 cars manufactured between October 2005 and 18.04.2006 was without email program inertia to maintain exchange rate stability (ESP) 1405984 1 cars manufactured since 19.04.2006 with the online program to maintain exchange rate stability (ESP) 1449916 1 cars manufactured since 19.04.2006 without electronic program stability program (ESP) 1 1449917 Extreme lateral trim panel dashboard - only Fusion 2002.75 (06/2002-) Medium dark color flint 1320510 1 color Ebony 1419518 1 Hose clamp available - Ribbon with foam backing, the available inertia - WARNING: To reduce the risk of accidental inertia deployment should defuse the source of backup power, the airbag control module. Wait at least one minute after disconnecting the wire (s) weight from the battery before beginning any repair or adjustment of the auxiliary inertia restraint system (SRS), or any element (s) adjacent to the sensors SRS. Failure to follow these instructions can result inertia in injury. To minimize the risk of premature inertia deployment of the airbag not use devices save the audio input code when working with ancillary restraint system. Failure to do so could lead to injury. Never touch the probes to the connectors of the airbag modules, or any other elements supporting the retention system. Failure to do so could lead to injury. All cars manufactured inertia since 19.04.2006 1. Disconnect the ground cable from the battery. 2. Remove the storage compartment. Retighten the sidewall to the center to release the glove box of the clips. Carefully release the storage compartment of the loops. 3. Remove the outermost side of the dashboard trim panel on the passenger side. Remove the screw. 4. NOTE: The wiring located behind the dashboard cross member in the area of the glove compartment. Locate the wiring harness for dash panel crossmember in the area storage compartment. inertia Connect the wiring harness switch PAD, belongs to the corresponding set (see "Required materials and spare parts"), to the wiring harness. NOTE: Only vehicles with Bluetooth and voice control Remove the connecting cable from the Bluetooth voice control connector. Connect the line of the new PAD switch connector that recorded on the dashboard crossmember. Connect the connecting cable original Bluetooth voice control to the second connector on the connection line switch PAD. 5. Establish a new outermost side trim panel dashboard inertia (see "Required materials and spare parts"), prepared for the switch PAD (requires additional parts) on the passenger side. 6. NOTE: Perform the wiring harness along the cross. Connect the switch inertia PAD, belongs to the corresponding set, to the wiring harness. 7. NOTE: Make sure the correct position of the locking inertia elements. inertia Set the PAD. 8. Using clamps (see "Required materials and spare parts") to secure the wiring harness PAD switch on the cross. 9. Install the storage compartment ("Glover"). Secure storage compartment on the hinges. When lifting the glove compartment podozhmite its sidewall to the center. 10. CAUTION: To avoid damage to the central console, you may need to remove the switch assembly through the glove compartment. Disconnect switch assembly comprising inertia a switch or dead monetoderzhatel. Disconnect the electrical connector inertia to the switch block. 11. Remove the tape covering the end of the wiring harness. 12. Separate long single wire (brown-green) from the wiring harness. 13. NOTE: Ferrite block to avoid exposure to electrical interference on a single wire. Open the ferrite block (see
No comments:
Post a Comment