Discussion and reviews: DAIM - 05.05.2014 Why reinvent the wheel? Especially in the situation descr

Load switch, perhaps, the first device in the queue to be installed in panel with modulkoy as an input device, and of the general switch. It's called switch disconnector - disconnector. Cutout, simply put. And though the imagination the word "cutout" tečajna lista draws YABPVU, load switch does exactly the same thing only without tečajna lista fusible plugs, well and generally any protection.
Directly hero of this post available at the moment, and if possible, it is extremely tečajna lista difficult, but most likely willing to buy load switch EASY9 can do it after the new year when Schneider Electric will close all issues with supplies.
Short link for this post: http://bit.ly/1n6GWxo Commented - 9
Extremely pleasant thing! And, as I understand it, in all denominations will be bridged contacts! as soon as the warehouses of our local suppliers - I will always use them. although IEKovsky HV-32 is also not bad at all
And what is the advantage of using the switch / circuit breaker compared tečajna lista with a circuit breaker? tečajna lista After all circuit breakers are surprisingly tečajna lista expensive. Why not just put the machine enough denomination? At the same time, and the defense will? This is not trolling, just wondering, I can not consider any factors?
Load switches IEK BH-32 and BH-100 DEKraft are inexpensive and have the same advantages. 1. Simplicity of design, and therefore, reliability. 2. Rigid handle communication with contacts provides guaranteed open circuit, or makes it clear that contacts boiled, and the chain break is not possible. 3. Substantially greater contact area. 4. Dvuhpolyunye IEKi Decks and have a bunch of unrecoverable mechanism with simultaneous shutdown poles.
For what? Design decision do not provide for any automatic. If there is a batchfile and so it must be replaced by something similar, but not to limit the consumer to the PTO. Is not it so?
always believed that the PTO is limited bandwidth meter. Old 40 A new 50 and even 60 have. In new houses have long since nobody batchfile nestavit (design decision), and put before the opening automatic counter. 50 And at the apartment. If you put as you say (if anything on you?), The scheme is a more expensive: BH-meter-VvodnoyVA-rguppovye VA. Here, in this as if no smysla.S respect.
Jeka, there is even and 80A, and even you will not believe, at 100A. But, in order. 1. PUE should stand before the meter shut-off device - it or switch or circuit breaker. 2. Machines front of the counter to give protection for the most counters for main machine in the ASU does not protect them, in any case, if you type in the floor panel in front of the counter tečajna lista cutout stands at the feeder downstream of the meter should be automatic. 3. If the floor board courier costs, it makes sense to put machine on entering the apartment panel? According to the norms, if all group lines apartment shield protected introductory unit may not be installed. Based on the selectivity in the housing panel machine must be smaller value, at least on stage. This was discussed many times in different forums (about downhill to floored visor). A simple example: in floor panel AB C50, C40 AB in apart. Operating range 5-10In. 50h5 = 250A, 400A = 40x10. Here you and selectivity. TS if you put denominated smaller 2 stage weaning allowed power is obvious. 4. GOST R 51628-2000 There Shields for residential buildings, tables 2 and 4, which clearly states that where to put. 5. And yet, electrical endurance, switching cycles, not less than 10,000 for HV-32 IAC (switch), not less than 6000 for VA47-29-29M, -60, -100 (machines). .6. And finally: VA47-29 3P 63A 4.5 kA - 162rub. VA47-60 3P 63A 6kA - 272rub. BH-32 3P 63A (100A) - 162rub And you say is a more expensive scheme. All the best!
Discussion and reviews: DAIM - 05.05.2014 Why reinvent the wheel? Especially in the situation described by me, he can not help. Assume the output voltage has USM, and the road to ... Victor - 04.05.2014 Love LK. Where better bucket type Legrand Artem - 04.05.2014 As it does not happen, I suppose, the work experience of 13 years finisher wagon, apartments throughout the city made me a turnkey, from simple to complex and expensive pipets and ... Artem - 04.05 .2014 absolutely agree smol - 02.05.2014 Why not put in USM and shield beneath RCBO IZI9. All issues discussed close. And even more :-) Alex - 30.04.2014 However, the sample Legrand can not provide, because they do not have one-and-Akiha huge money in the budget. :) So, vordstate say that no, this module does not look ... Igor - 04/28/2014 Good afternoon, gentlemen. There is such a device from Legrand: POP-Power Overvoltage Protection (I already tečajna lista showed its specialists from the company). He's in one module and ... DAIM - 27.04.2014 At least theoretically electromechanical differential or RCBO RCD better. If switched on from the entrance RCBO disable zero and